manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 43 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 43

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

43

At power-on

After the power-on sequence has 
started, the LED turns off and the 
printer does not operate.

Main Board

1. Check that the Relay connector of the ASF Motor and the Relay 

connector of the Pump Motor are not connected to the wrong 
connectors causing a short circuit.

1. Connect the Relay Connector of the ASF 

Motor and the Relay Connector of the Pump 
Motor correctly, and replace the Main Board 
with a new one.

At operation

Operation at power-on is normal, 
but an error appears when the 
print job is sent to the printer.

Interface cable

1. Check that the Interface cable is connected between the PC and 

the printer.

1. Connect the Interface cable to the PC and the 

printer.

2. Check the Interface cable for breaking.

2. Replace the Interface cable with a new one.

EPSON
USB driver

1. When using USB, check that the EPSON USB driver has been 

installed on the PC.

1. Install the EPSON USB driver.

USB

1. Check that the PC and printer are connected via the USB hub.

1. Enter the USB serial No. indicated on the 

product nameplate.
Refer to Chapter 5 

"ADJUSTMENT"

.

Printer Driver

1. Check that the printer driver for Stylus Photo 1390/1400/1410 

has already been installed.

1. Install the printer driver for Stylus Photo 1390/

1400/1410.

2. Check that the connected printer is EPSON Stylus Photo 1390/

1400/1410.

2. Connect the Stylus Photo 1390/1400/1410 

printer.

Main Board

1. Check that a wrong model name has not been input to the 

EEPROM address on the Main Board.

1. Using the Adjustment Program, enter the 

correct model name.
Refer to Chapter 5

"ADJUSTMENT"

.

Table 3-2.  Troubleshooting of Communication Error

Occurrence 

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

Relay Connector of 

the Pump Motor

Relay Connector of 

the ASF Motor

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов