Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 93

Страница: 93 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

5. Release the coil section of Torsion Spring 24.7 from the tab on the Left CR Shaft

Mounting Plate with tweezers.

Figure 4-42. Removing the Torsion Spring 24.7 (1)

6. Remove Torsion Spring 24.7 from the CR Scale following the next steps:

6-1.

Bring the coil section to an upright position.

6-2.

Push downwards to release foot 1 from the cutout on the Left CR Shaft
Mounting Plate.

6-3.

Turn the coil section counterclockwise.

6-4.

Remove Torsion Spring 24.7 from the hole on the CR Scale.

Figure 4-43. Removing the Torsion Spring 24.7 (2)

7. Turn the CR Scale 90°, and remove it from the tab on the Left CR Shaft Mounting

Plate.

Figure 4-44. Removing the CR Scale

Left CR Shaft

Mounting Plate

Torsion Spring 24.7

Tab

Step 6-1

Step 6-2

Step 6-3

Foot 1

Cutout

Tab

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 93 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: