Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 53

Страница: 53 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

Table 3-11. Troubleshooting of Fatal Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At power-on

At power-on, the CR Motor does
not operate at all.

CR Motor

1. Check that the CR Motor connector cable is connected to the

Relay Connector.

1. Connect the CR Motor connector to the Relay

Connector.

2. Check the CR Motor connector cable for damages.

2. Replace the CR Motor with a new one.

3. Check if the CR Motor operates normally.

3. Replace the CR Motor with a new one.

Relay Connector
Cable
(for the CR
Motor)

1. Check that the Relay Connector Cable is connected to the Main

Board Connector CN6.

1. Connect the Relay Connector Cable to the

Main Board Connector CN6.

2. Check the Relay Connector Cable for damages.

2. Replace the Relay Connector Cable with a new

one.

CR Motor

Relay Connector

CN6

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 53 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: