Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 113

Страница: 113 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

113

4.2.6.10 Release Holder Assy

Remove the ASF Assy. See Section 4.2.4 on page 86.

2. Release the PE Sensor Connector Cable from the five tabs on the Release Holder

Assy.

3. Remove the three C.B.S. 3x6 screws that secure the Release Holder Assy.

4. Remove the three lower tabs of the Release Holder Assy from the Main Frame

with a flat-blade screwdriver, and remove the Release Holder Assy upwards.

Figure 4-107. Removing the Release Holder Assy

2) C.B.S. 3x6

(8±1 kgf.cm)

PE Sensor Connector Cable

Tabs

Release Holder Assy

Rear side

Upper Tabs

Lower Tabs

Front side

Align the three Upper tabs on the Release Holder Assy with the
positioning holes on the Main Frame.

See Figure 4-107.

Fit the FLAG Release Shaft by the Bushings on the Release
Holder Assy.

Figure 4-108. Reinstalling the Release Holder Assy

Tighten the screws in the order shown in

Figure 4-107.

Bushings

FLAG Release Shaft

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 113 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: