Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 122

Страница: 122 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

122

4.2.7 Removing the Motors

4.2.7.1 CR Motor

1. Remove the Upper Housing.

For Stylus Photo 1400/1410:

See section 4.2.1.4 on page 80.

For Stylus Photo 1390:

See section 4.3.1 on page 128.

2. Release the Carriage lock, and move the Carriage Unit to the center.

See section 4.2.1.3 on page 79.

3. Disconnect the CR Motor Connector Cable from the Relay Connector.

Figure 4-132. Removing the CR Motor Connector Cable

4. Push the Driven Pulley toward the center to loosen the CR Drive Belt, and remove

the CR Drive Belt from the CR Motor Pinion Gear.

5. Remove the two C.B.S. 3x4 screws that secure the CR Motor, and remove the CR

Motor from the Main Frame.

Figure 4-133. Removing the CR Motor

CR Motor

Relay Connector

CR Motor Connector

Cable

CR Drive Belt

Driven Pulley

CR Motor Pinion Gear

Face the Lot No. printed surface of the CR Motor as shown in

Figure 4-134.

Figure 4-134. Installing the CR Motor

Tighten the screws in the order shown in

Figure 4-133.

A D J U S T M E N T

R E Q U I R E D

After replacing the CR Motor, the following adjustment must be
performed.

CR Motor Drive Dispersion

(p.133)

Refer to Chapter 5 “Adjustment” for details on the adjustments.

10) C.B.S. 3x4

(4±0.5 kgf.cm)

Lot No. Printed Surface

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 122 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: