manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 31 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 31

EPSON Stylus Photo 1390/1400/1410

Revision B

OPERATING PRINCIPLES

Printer Mechanism

31

The fed paper is detected by the PE Sensor, and its front end is then transferred to the 
front of the Front Paper Guide.
To eliminate the deflection of the paper, the paper is then returned toward the ASF 
Assy by the specified number of steps according to the paper feeding mode.
The paper is re-transferred to the specified paper locating position of the Front Paper 
Guide.

2.2.4.2  PF Measurement Sequence

†

The mechanical load in the paper feeding path is measured in the following cases 
to perform control so that an adequate current value is set according to the 
mechanical load.

„

When power is switched on

„

When the Ink Cartridge is replaced

†

When the mechanical load in the paper feeding path reaches the specified value, 
Fatal Error is displayed.

2.2.5  Ink System Mechanism

The Ink System Mechanism consists of the following units.

†

Pump Unit (including the CR Lock Lever)

†

Cap Unit

2.2.5.1  Pump Unit

The Pump Unit is designed to suck ink from the Printhead or Cap Unit. The Cap Unit 
has a built-in Head Cleaning Wiper.
The following shows the specifications of the stepping motor that drives the Pump 
Unit.

The following operations are performed when the drive of the Pump Motor is 
transmitted to the Pump Unit.

Note * : The direction (CW or CCW) was determined by viewing the motor from the output 

shaft of the motor mounting plate.

Table 2-7.  Pump Motor Specifications

Item

Specifications

Type

4-phase, 48-pole PM type stepping motor

Drive voltage

+42V ± 5% (voltage applied to driver)

Winding resistance

10.3

Ω

 ± 10% (per phase at 25°C)

Inductance

13.4mH ± 20% (1kH,1Vrms)

Drive method

Bipolar drive/constant-current drive

Drive IC

A6628

Table 2-8.  Pump Motor Rotation Directions and Functions

Pump Motor Rotation Direction*

Functions

CW direction

• Cap closing
• Ink suction
• Wiper resetting
• CR Lock setting

CCW direction

• Cap opening
• Pump release
• Wiper setting
• CR Lock resetting

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов