manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 33 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 33

EPSON Stylus Photo 1390/1400/1410

Revision B

OPERATING PRINCIPLES

Printer Mechanism

33

2.2.5.3  Cap Unit

The Cap Unit is designed to keep inside of the Cap airtight by the Cap sticking to the 
Printhead surface with the driving force of the Pump Motor when ink is sucked.
When the printer is in a standby status or its power is OFF, the Cap Unit prevents the 
ink from thickening.

The following figures shows the Cap Unit operation.

Figure 2-11.  Capping Mechanism

2.2.6  Ink Sequence

The following ink sequence is executed according to various timer, counter, flag and 
other information saved on the EEPROM.

†

Initial Ink Filling
When the printer is powered on for the first time after purchase, the printer 
executes the initial ink filling operation to fill the ink cavities of the Head with ink. 
When the initial ink filling operation is performed properly, the printer clears the 
flag in the EEPROM so that initial ink filling operation will not be performed 
when it is powered on the next time. The EPSON Stylus Photo 1390/1400/1410 
requires about 170 seconds to perform the initial ink filling operation.
If the sequence does not end normally during initial filling, the initial filling flag is 
not cleared and the CL operating flag is set. Because of these flags, when powered 
on the next time, the printer assumes that it was powered off for some reason 
during initial filling and executes CL3 instead of the initial filling sequence. (On 
the previous model, initial filling was executed again. However, when this 
operation was performed, ink was wasted and therefore CL3 is executed to cover 
for the ink filling performance.)
When the initial filling flag is set and the CL operating flag is not set, the printer 
judges that the initial filling was not executed at all (power was switched on but 
the cartridges were not installed), and when the printer is powered on the next 
time, it executes initial filling.

†

Replacement Cleaning
Replacement cleaning is executed when an Ink Cartridge(s) is replaced.

Slider cap rises to perform 
capping.

Printhead

Cap

Carriage Unit

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов