Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 118

Страница: 118 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

118

6. Slide the Front Paper Eject Roller to the left, and remove the Left Bushing 8 from

the Main Frame.

Figure 4-119. Removing the Left Bushing 8

7. Return the Carriage Unit to its home position.

8. Release the tab that secures the Front Paper Guide from the Main Frame and slide

the Front Paper Guide to the left, and turn it until the front side faces up to remove
the Front Paper Guide together with the Paper Eject Roller.

Figure 4-120. Removing the Front Paper Guide and Paper Eject Rollers

Front Paper Eject Roller

Tab

Front Paper Eject

Roller

Front Paper

Guide

Rear Paper Eject

Roller

Align the Bushing of the Front Paper Guide with the PF Roller
Shaft.

Figure 4-121. The PF Roller Shaft and the Bushing of the

Front Paper Guide

Align the positioning holes on the Main Frame with the Guide
Pins on the Front Paper Guide.

Figure 4-122. Installing the Front Paper Guide

Shaft and Bushing

Positioning Holes and

Guide Pins

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 118 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: