Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 95

Страница: 95 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

5. Using the special tool (refer to

p75

), disengage tab B of the CSIC Assy on the right

rear side of the Carriage Unit.

Figure 4-50. Removing the CSIC Assy (2)

6. Lift up the CSIC Assy from the Carriage Unit to disconnect the CSIC FFC, and

remove the CSIC Assy.

Figure 4-51. Removing the CSIC Assy (3)

4.2.6.3 Printhead

Remove the CSIC Assy. See Section 4.2.6.2 on page 94.

2. Remove the three C.B.P. 2.6x8 screws that secure the Printhead using Phillips

Screw Driver, No.1, and remove the Printhead by lifting it up vertically.

Figure 4-52. Removing the Printhead (1)

3. Disconnect the two Head FFCs on the back side, and remove the Printhead.

Figure 4-53. Removing the Printhead (2)

Tab B

Carriage Unit

Tab B

Removal Direction

CSIC Assy

CSIC FFC

Rear side of CSIC Assy

Connector

Hook

7) C.B.P. 2.6x8

(3±0.5 kgf.cm)

Head FFC

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 95 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: