manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 4 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 4

About This Manual

This manual describes basic functions, theory of electrical and mechanical operations, maintenance, and repair procedures of the printer. 
The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page.

Manual Configuration

This manual consists of six chapters and Appendix.

CHAPTER 1. PRODUCT DESCRIPTIONS

Provides a general overview and specifications of the product.

CHAPTER 2. OPERATING PRINCIPLES

Describes the theory of electrical and mechanical operations of the 
product.

CHAPTER 3. TROUBLESHOOTING

Describes the step-by-step procedures for the troubleshooting. 

CHAPTER 4. DISASSEMBLY / ASSEMBLY

Describes the step-by-step procedures for disassembling and 
assembling the product.

CHAPTER 5. ADJUSTMENT

Provides Epson-approved methods for adjustment.

CHAPTER 6. MAINTENANCE

Provides preventive maintenance procedures and the list of Epson-
approved lubricants and adhesives required for servicing the product.

APPENDIX

Provides the following additional information for reference:
• Connector summary
• Electric circuit diagrams

Symbols Used in this Manual

Various symbols are used throughout this manual either to provide additional 
information on a specific topic or to warn of possible danger present during a 
procedure or an action. Be aware of all symbols when they are used, and always read 
NOTE, CAUTION, and WARNING messages.

Indicates an operating or maintenance procedure, practice or condition 
that, if not strictly observed, could result in injury.

Indicates an operating or maintenance procedure, practice, or condition 
that, if not strictly observed, could result in damage to, or destruction of 
equipment.

May indicate an operating or maintenance procedure, practice or 
condition that is necessary to accomplish a task efficiently. It may also 
provide additional information that is related to a specific subject, or 
comment on the results achieved through a previous action.

Indicates a product reassembly procedure, practice or condition that 
must be executed in accordance with the specified standards to maintain 
the product’s quality.

Indicates an operating or maintenance procedure, practice or condition 
that must be executed in accordance with the specified standards to 
maintain the product’s quality.

W A R N I N G

C A U T I O N

C H E C K

P O I N T

A D J U S T M E N T

R E Q U I R E D

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов