manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 151 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 151

EPSON Stylus Photo 1390/1400/1410

Revision B

MAINTENANCE

Overview

151

6.1.4  Lubrication

The lubrication used for the components of the printer has been decided on bases of 
evaluation carried out by Epson. The specified type of grease and the amount, and 
places of lubrication given in this section should be strictly observed.

Figure 6-2.  Lubrication (1)

Figure 6-3.  Lubrication (2)

C A U T I O N

„

Never use oil or grease other than those specified in this 
manual. Use of different types of oil or grease may damage the 
components or affect the printer functions.

„

Never apply a larger amount of oil or grease than specified in 
this manual.

Table 6-1.  Grease Applied to the Stylus Photo 1390/1400/1410

Type

Name

EPSON CODE

Supplier

Grease

G-26

1080614

EPSON

Grease

G-45

1033657

EPSON

Grease

G-71

1304682

EPSON

<Lubrication Point>
Left and Right Adjust Parallel Bushings 
(outer circumference)

<Lubrication Type>
G-26

<Lubrication Amount>

φ

1mm x 2mm

<Remarks>
• Apply with a syringe.

(Pin Head: 

φ

1mm)

• After lubrication, install and turn the 

PG Cam Bush to spread the grease 
evenly.

<Lubrication Point>
Contact points of the CR Scale Mounting 
Plate (Left/Right) and the Main Frame

<Lubrication Type>
G-26

<Lubrication Amount>
Apply evenly.

<Remarks>
Apply with a brush.

Right Side Face

Adjust Parallel Bushing (Right)

Left Side Face

Adjust Parallel Bushing (Left)

Left Side

Right Side

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов