Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 44

Страница: 44 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

Note *:

Stylus Photo 1390 does not have the CD/DVD-related units.

Table 3-3. Troubleshooting of Cover Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

During printing*

A Cover Open (Tray) Error is
indicated during printing.

Printer Cove

1. Check that the CD-R Unit is not open.

1. Close the CD-R Unit.

Table 3-4. Troubleshooting of Paper Out Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At operation

When the Paper button is
pressed, the LD Roller attempt to
feed paper but the paper is not
fed.

ASF Assy.

1. Check the LD Roller or Retard Roller of the ASF Assy for paper

dust and foreign matter.

1. Using a cleaning sheet (part code:1262115),

clean the LD Roller and Retard Roller.
The procedure is as follows.

(1) Place the cleaning sheet upside down and

put it into the ASF Assy.

(2) Press the Paper button to start paper feed.
(3) Repeat the above steps several times.

* To remove persistent contamination,

staple an alcohol-dampened cloth to a
postcard and clean the rollers in the
following method.

(1) Place the alcohol-dampened cloth facing

to the LD Roller surface of the ASF Assy.

(2) Hold the mount top end securely and

press the Paper button.

(3) Repeat the paper feed sequence several

times to clean the LD Roller surface of
the ASF Assy.

Cleaning sheet

Postcard used

as mount

Non-adhesive part

Adhesive part

This side down

Stapling

Cloth damped

with alcohol

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 44 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: