Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 46

Страница: 46 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

The Paper button
was pressed at the
setting of the CD/
DVD Tray.*

The CD/DVD Tray HP detection
sequence stops and the Tray is
ejected.

CD/DVD Tray

1. Check the HP detection position or white markings of the CD/

DVD Tray for paper dust and foreign matter.

1. Remove paper dust and/or foreign matter from

the detection position.

2. Check the Driven Roller surface for contamination such as paper

dust and CD-R coating material.

2. Feed A4-size sheets of plain paper from the

ASF Assy several times to remove the
contamination.

3. Check that the HP detection position or white markings of the

CD/DVD Tray are not chipped.

3. Replace the CD/DVD Tray with a new one.

The CD/DVD Tray is fed toward
the ASF Assy, but is ejected
immediately.

PW sensor

1. Check the PW Sensor for contamination such as paper dust,

ink, etc.

1. Clean the PW Sensor surface.

2. Compare the EEPROM values in two places and check that they

are not approximated to each other.

2. Replace the PW Sensor with a new one.

Table 3-4. Troubleshooting of Paper Out Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

White Markings

HP detection

position

PW sensor

Carriage Unit Bottom

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 46 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: