manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 49 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 49

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

49

Note *:

Stylus Photo 1390 does not have the CD/DVD-related units.

Table 3-6.  Troubleshooting of Paper Mismatch Error

Occurrence 

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At operation*

When feeding a CD-R (Board 
Paper), an error is displayed on 
the LED and STM3.

Paper EJ Frame 
Assy
(CD/DVD Tray 
Base)

1. Check if the CD/DVD Tray Base is closed or not.

1. Open the CD/DVD Tray Base.

CD-R Sensor

1. Check that the Connector cable of the CD-R Sensor is securely 

connected to the connectors of the CD-R Sensor and Panel 
Board.

1. Connect the Connector cable of the CD-R 

Sensor to the CD-R Sensor and Panel Board 
Connectors.

2. Check the CD-R Sensor or Connector cable for damages.

2. Replace the CD-R Sensor with a new one.

Panel Board connector

Connector cable of 

the CD-R Sensor

CD-R Sensor

Table 3-7.  Troubleshooting of Ink Low

Occurrence 

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At operation or 
during printing

A message is displayed on the 
LED and STM3 during 
printing.

Ink Cartridge

1. Look at the remaining ink indication of the STM3 to check the 

amount of the ink remaining in the Ink Cartridge.

1. Prepare a new Ink Cartridge.

Table 3-8.  Troubleshooting of Ink End Error

Occurrence 

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

During printing

After the Carriage has detected 
the HP, an error is displayed on 
the LED and STM3.

Ink Cartridge

1. Look at the remaining ink indication of the STM3 to check 

whether the ink remains in the Ink Cartridge.

1. Replace the Ink Cartridge with a new one.

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов