Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 86

Страница: 86 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

4.2.4 ASF Assy

1. Remove the Upper Housing.

For Stylus Photo 1400/1410:

See section 4.2.1.4 on page 80.

For Stylus Photo 1390:

See section 4.3.1 on page 128.

2. Remove the screw C.B.S. 3x8 that secures the Earth Cables positioned on the right

rear side of the printer, and remove the Earth Cables.

3. Disconnect the ASF Motor Connector from the Relay Connector.

4. Disconnect the Relay Connector Cable from the ASF Assy.

Figure 4-27. Releasing the Cables (1)

5. Disconnect all the Cables and the FFCs from the connectors on the Relay Board.

CN1 : Relay FFC

CN2 : PE Sensor Cable

CN4 : APG Sensor Cable (downside)

CN5 : APG Sensor Cable (the upper side)

CN6 : PF Encoder Sensor FFC

6. Disconnect the FFC bundled by the Acetate Tape 2 from the connectors (CN5,

CN10, CN11, CN12, CN14, CN15) on the Main Board, and release it from the
groove of the ASF Assy.

7. Remove the Acetate Tape 2, and disconnect the APG Motor Cable and PE Sensor

Cable from the ASF Assy.

8. Peel off the PF Encoder FFC secured by two pieces of double-sided adhesive tape

from the ASF Assy.

Figure 4-28. Releasing the Cables (2)

Secure the two Earth Cables together with the screw.

Referring to

Figure 4-27

, correctly route the Relay Connector

Cable.

5) C.B.S. 3x8

(8±1 kgf.cm)

Relay

Connector

Earth Cables

Relay

Connector

Cable

Ferrite Core

ASF Motor

ASF Assy

Two-sided

Tapes

CN5, CN10, CN11,

CN12, CN14, CN15

Main Board

Relay Board

PF Encoder Sensor FFC

Acetate Tape 1

Groove

APG Motor Cable

PE Sensor Cable

Acetate Tape 2

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 86 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: