manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 136 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 136

EPSON Stylus Photo 1390/1400/1410

Revision B

ADJUSTMENT

Adjustment Items and Overview

136

Note : Symbol explanation

~

 After removing or replacing the part

{

 After replacing the part

Note  1 : When data can be read from the old board.

 2 : When data cannot be read from the old board.

 3 : Nozzle check patterns must be printed for confirmation.

 4 : Perform this adjustment when replacing the mechanical unit with a rebuilt one 

whose PF Roller is not new.

 5 : This adjustment is required only when the Left Parallelism Adjust Bushing is moved.

Table 5-4.  Replacement Part-Based Adjustment Item and Priority List (2)

Adjustment Item

Priority

Carriage 

Shaft

Carriage Unit

PF Motor

Paper EJ Frame 

Assy.

PF Roller 

Shaft

Front Paper 

Guide/Paper 

Eject Roller

ASP 

Mechanism 

Unit

ASF Assy

PF Belt Tension Adjustment

1

–

–

~

–

~

–

–

–

PF Roller Shaft Center Support Position 
Adjustment

2

–

–

~

–

~

–

–

–

PG Adjustment

3

~

~

–

–

~

 

5

–

{

–

Reading and Writing Main Board Data

4

–

–

–

–

–

–

–

–

Initial Value Write

5

–

–

–

–

–

–

–

–

USB ID Input

6

–

–

–

–

–

–

–

–

Head ID Input

7

–

–

–

–

–

–

–

–

Head Angular Adjustment

 8

{

{

–

–

–

–

{

–

Bi-D Adjustment

 9 

3

{

{

–

–

–

–

{

–

First Dot Position

10

{

{

–

–

–

–

{

~

PW Sensor Adjustment

11

{

{

–

~

~

~

{

–

PF Deterioration Compensation Counter Reset

12

–

–

–

–

–

–

{

–

PF Deterioration Compensation Counter Reset
(write the maximum value) 

4

13

–

–

–

–

–

–

–

–

PF Adjustment

14

–

–

~

~

~

~

{

–

PF Adjustment (Bottom Margin)

15

–

–

~

~

~

~

{

–

Waste Ink Counter Reset

16

–

–

–

–

–

–

–

–

CR Motor Drive Dispersion

17

–

–

–

–

–

–

{

–

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов