Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 96

Страница: 96 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

4.2.6.4 APG Assy

1. Remove the Upper Housing.

For Stylus Photo 1400/1410:

See section 4.2.1.4 on page 80.

For Stylus Photo 1390:

See section 4.3.1 on page 128.

2. Disconnect the APF Motor Cable from connector CN9 (red) on the Main Board
3. Remove the acetate tape, and remove the Cable from the ASF Assy.
4. Disconnect the Connector Cables from the two APG Sensor Connectors.

Figure 4-54. Disconnecting the Connector Cables

5. Remove the three C.B.S. 3x6 screws that secure the APG Assy and remove the

APG Assy from the Main Frame.

Figure 4-55. Removing the APG Assy

Tighten the screws in the order shown in

Figure 4-52.

A D J U S T M E N T

R E Q U I R E D

After replacing or removing the Printhead, the following
adjustment must be performed.

1. PG Adjustment

(p.132)

2. Head ID Input (only after replacing)

(p.132)

3. Head Angular Adjustment

(p.132)

4. Bi-D Adjustment

(p.132)

5. First dot position

(p.133)

6. PW Sensor Adjustment

(p.133)

Refer to Chapter 5 “Adjustment” for details on the adjustments.

CN9

APG Motor

APG Assy

APG Sensor Connectors

Acetate Tape

2) C.B.S. 3x6

(8±1 kgf.cm)

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 96 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: