Endress+Hauser Topclean S CPC30 Скачать руководство пользователя страница 112

Страница: 112 / 178

6 Commissioning

Topclean S

112

Hauser

6.6.19

Calibration

Note!
The defaults for on-site calibration are made in the menu
"PARAM"

➠

"Set up 1"

➠

"Calibration" (see page 67 for pH / page 70 for Redox).

The calibration can be protected with the maintenance and the specialist codes (compare with
page 58).

Procedure:

Switch the service switch to "Service" (vertical) or move the assembly to service position.
Otherwise, calibration is not possible.

Remove electrode.

Clean electrode before calibration.

Note!
• For measurements with PML (potential matching), the PM line must be immersed in the buffer

solution.

• If automatic temperature compensation is selected for calibration (ATC), the corresponding

temperature sensor must also be immersed in the buffer solution.

• The instrument switches automatically to Hold (factory setting) whenever it is calibrated.
• Cancel calibration by pressing the "MEAS" key.

The following section describes the calibration procedures for:

• If you confirm this with "yes, cancel cal.", you return to the

measurement mode.

• If you select "no", calibration is continued.

pH calibration

➠

"Manual data entry" (see page 113)

➠

"Manual calibration with buffer" (see page 114)

➠

"Calibration with fixed buffer" (see page 114)

➠

"Calibration with automatic buffer recognition"
(see page 114)

Redox absolute calibration

➠

"Absolute data entry" (see page 115)

➠

"Absolute calibration" (see page 116)

Redox relative calibration

➠

"Absolute data entry" (see page 116)

➠

"Relative data entry" (see page 118)

➠

"Absolute calibration" (see page 117)

➠

"Relative calibration" (see page 118)

7.00

Cal

Edit

Cancel Calib.

yes, Cancel Calib.

yes,

Содержание Topclean S CPC30



















































































































































































Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды

Endress+Hauser Topclean S CPC30, Руководство по эксплуатации

Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды