Endress+Hauser Topclean S CPC30 Скачать руководство пользователя страница 24

Страница: 24 / 178

4 Wiring and pneumatic connection of Topclean S

Topclean S

Hauser

Changing the pH input from glass electrode to ISFET sensor

The Topclean S version glass/ISFET (CPC30-xx2xxxxxxx) is factory set for measurement with glass
electrodes.

To adapt the electrical connection for ISFET sensors, please proceed as follows:

Open the lower housing section of the CPM153.

If a glass electrode is connected, remove the wires of the electrode cable.

Remove the "pH" terminal located at the housing cover and replace it by the included terminal
"DRN" / "SRC".

C07-CPM153xx-04-06-06-xx-004.eps

ƒig. 17:

pH terminal at the housing cover

Open the housing cover of the CPM153.

On the right side of the housing cover, pull off both ends of the red cable to the pH input (see
fig. 18).

Pin up the jumpers included as shown in fig. 19.

Connect the sensor cable according to the wire assignment for ISFET sensors.

Change the setting "electrode type" in the First start up menu (p. 51) to "ISFET".

Note!
Please switch from ISFET sensor to glass electrode correspondingly.

C07-CPM153xx-04-06-06-xx-002.eps

ƒig. 18:

pH input module and pH terminal set in
housing cover with cable (red) for connection
of pH / redox glass electrodes.

C07-CPM153xx-04-06-06-xx-003.eps

ƒig. 19:

pH input module and pH terminal set in

housing cover with jumpers for connection of ISFET
sensors

Содержание Topclean S CPC30



















































































































































































Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды

Endress+Hauser Topclean S CPC30, Руководство по эксплуатации

Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды