Endress+Hauser Topclean S CPC30 Скачать руководство пользователя страница 63

Страница: 63 / 178

Topclean S

6 Commissioning

Hauser

To enter the menu, proceed as follows:

⇒

PARAM

7.00

Param

Parametrieren

Grundeinstellung

Sonderfunktionen
Handbedienung

Quick

Setup

Edit

Weiter E

7.00

Hold

Param

Settings

Set up 1

Set up 2
Manual operation

First start up

Edit

Next E

7.00

Param

Edit

Set up 1

Hold

Relays

Temperature

Alarm

Hold
Calibration

CHOICE
(default = bold)

INFO

Temp. comp. sensor

Temp. comp. process

Selection for temperature compensation
Temp. comp. sensor

= automatic (ATC) or manual (MTC)

temperature compensation.

Temp. comp. process

(only for pH) = compensation of the

medium temperature using customer-specific tables (see below).

Temperature compensation sensor:

ATC C1

MTC
MTC+Temp.

Select temperature compensation
ATC

= automatic temperature compensation with a temperature

sensor circuit

MTC

= manual temp. comp. (with fixed temperature, entered in

the following field)

MTC+Temp.

= as MTC. The display, however, shows the value of

the temperature sensor connected to the temperature input of the
transmitter.

025.0 °C

(0 ... 100.0 °C)

MTC temperature

(only pH, MTC)
Temperature entry for manual compensation

off

Select temperature measurement

(only redox)
The reference temperature can be adapted according to customer
specifics in the field "Reference temperature" (last field of this
menu).

Pt 100

Pt 1000
NTC 30
none

Select temperature sensor

Note!

This selection is not available for digital sensors with Memosens
technology.

Adjust temp. reading

(–20.0 ... 150.0 °C)

Enter actual temperature for temperature calibration

The value currently measured by the temperature sensor can be
changed/adapted. The temperature difference is stored internally as
an offset value.

0.0 °C

(-5.0 ... 5.0 °C)

Edit offset

The offset value obtained from the previous field can be edited or
reset here.

Hold

7. 00

[E]

Select

Edit[¯]

Param

Temp. comp. sensor

Temp. comp. process

Hold

7. 00

[E]

Temp.comp. 1

Edit[¯]

Param

ATC C1

MTC
MTC+Temp

Содержание Topclean S CPC30



















































































































































































Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды

Endress+Hauser Topclean S CPC30, Руководство по эксплуатации

Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды