Endress+Hauser Topclean S CPC30 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 178

background image

Topclean S

4 Wiring and pneumatic connection of Topclean S

Hauser

33

4.3

Topclean S hosing

4.3.1

Compressed air

C07-CPC30xxx-04-12-00-en-008.eps

ƒig. 28:

Connection of compressed air, rinse water, buffer and cleaning agent to CPG30

!

Note!

• The compressed air line and a T-piece must be provided by the operator.
• The air must be filtered (0.5 µm), free of oil and condensate. The minimum line diameter is

10 mm / 0.39".

1.

Screw the manometer into the thread of the pressure reduction valve.
It regulates the air pressure (optimum 5 bar / 72.5 psi).

2.

Connect the compressed air supply to the pressure reduction valve.

"

Caution!
Observe the installation direction of the pressure reduction valve. The flow direction is
indicated by arrows on the top of the rectangular valve block.

3.

Connect the compressed air line from the reduction valve outlet to the connection I. Apply a
pressure of 4 to 6 bar / 43.5 to 87 psi. Tighten the cable glands

by hand

(approx. 0.5 Nm).

!

Note!
When using an Ex version of Topclean S, connect the compressed air lines for the CYR10 injector
to the connections "G" and "H" (for connection diagrams, see XA 236C).

«
...
31
32
33
34
35
...
»

Содержание Topclean S CPC30



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Topclean S CPC30

Бренд: Keithley Страницы: 148

Workstation Monitor 724

Бренд: 3M Страницы: 21

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 24

Бренд: 3M Страницы: 2

SoundPro SE Series

Бренд: 3M Страницы: 293

Бренд: Accurate Logic Страницы: 50

Acuvim-L Series

Бренд: AccuEnergy Страницы: 188

Бренд: VAMP Страницы: 78

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 16

Бренд: M & I Instruments Страницы: 2

Бренд: Vanguard Instruments Company Страницы: 62

Бренд: Vanguard Instruments Company Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды