Endress+Hauser Topclean S CPC30 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 178

background image

Topclean S

3 Installation

Hauser

11

3

Installation

3.1

Incoming acceptance, transport, storage

• Make sure the packaging is undamaged!

Inform the supplier about damage to the packaging.
Keep the damaged packaging until the matter has been settled.

• Make sure the contents are undamaged!

Inform the supplier about damage to the delivery contents.
Keep the damaged products until the matter has been settled.

• Check that the scope of delivery is complete and agrees with your order and the shipping

documents.

• The packaging material used to store or to transport the product must provide shock protection

and humidity protection. The original packaging offers the best protection.
Also, keep to the approved ambient conditions (see "Technical data").

• If you have any questions, please contact your supplier or your sales centre responsible (see back

page of these Operating Instructions).

3.2

Installation conditions

!

Note!
Always install the transmitter and the control unit so that the cable entries point downwards.
The components can be installed using the following methods:

Notes on installation

• The transmitter CPM153 is normally used as a field device.
• The transmitter CPM153 can be fixed to a vertical or horizontal pipe using the supplied mounting

kit. For outdoor installation, a weather protection cover CYY101 is required. It can be fitted to
the field device using all kinds of fixtures (refer to "Accessories").

Device

Wall mounting

Post/

pipe installation

Panel mounting

Control unit CPG30

Mounting kit contained in
scope of delivery.
See fig. 6.

not applicable

not applicable

Mycom S CPM153,

covered

Required:
2 screws dia. 6 mm
2 rawl plugs dia. 8 mm

Mounting kit contained in
scope of delivery. See fig. 9.

Mounting kit contained in
scope of delivery.
See fig. 9.

Mycom S CPM153,

outdoors

If installed outdoors, wea-
ther protection cover
CYY101 required
(see Accessories).

Weather protection cover
CYY101 and 2x round post
fixtures required
(see Accessories).

not usual

«
...
9
10
11
12
13
...
»

Содержание Topclean S CPC30



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Topclean S CPC30

Бренд: Oceanic Страницы: 17

Бренд: Harley Benton Страницы: 28

HYGRASREG KH-30

Бренд: S+S Regeltechnik Страницы: 16

Бренд: T&D Страницы: 2

Бренд: T&D Страницы: 2

GroundCast DRS611

Бренд: Vaisala Страницы: 12

Бренд: CONDTROL Страницы: 8

Бренд: Barksdale Страницы: 2

Vortex Flow Industry

Бренд: Grundfos Страницы: 16

Бренд: Spacelabs Страницы: 156

Бренд: Energometrika Страницы: 39

Бренд: BizLine Страницы: 62

Бренд: Hanna Instruments Страницы: 28

Бренд: Saluki Technology Страницы: 161

Бренд: Ofs Страницы: 28

DOC026.52.00769

Бренд: Hach Страницы: 64

Бренд: AccuEnergy Страницы: 23

Бренд: GW Instek Страницы: 91

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды