Endress+Hauser Topclean S CPC30 Скачать руководство пользователя страница 95

Страница: 95 / 178

Topclean S

6 Commissioning

Hauser

Copy day:

Tuesday
Wednesday
...
Sunday

? = Monday
Select day,

to which you want to copy Monday (example).

Note!

•

Danger of data loss

. When copying one day to another, the

cleaning programmes of the

target day

are overwritten.

• Leave this selection by pressing "PARAM".

Cleaning:

no progr.

Clean
Clean S

Select a programme

to be started in the case of soiling or blocking of the electrode.

Power failure programme:

Note in display (no entry)

Clean
Clean S

Select a programme

which will be launched if the power supply or the
communication fails.

User programme:

(Programme editor)

User prog. 1

User prog. 2
User prog. 3

Select user programme

With Topclean S, you have

three

user programmes available.

(With Chemoclean there is

one

user programme available.)

Edit

Insert programme
Configure
Enable
Disable
Rename

Select edit function

Insert programme

: An installed programme (e.g.

Clean

) can

be inserted into the user programme.

Note!

• After a programme is disabled, it can be reenabled at any

time.

• Leave this item by pressing "PARAM".
• If you edited a programme

for the first time

, you have to

configure it at least once so that you can enable/disable it.

CHOICE
(default = bold)

INFO

Hold

pH 7.00

Param

[E]

Edit[¯]

? = Monday

Tuesday

Wednesday

Thursday
Friday

Saturday

Hold

pH 7. 00

Param

[E]

PwrFail prg.

After power
failure or
communication
failure back up
program will be started

Hold

pH 7. 00

Param

[E]

Edit[¯]

User prog.

User prog. 1

User prog. 2
User prog. 3

Содержание Topclean S CPC30



















































































































































































Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды

Endress+Hauser Topclean S CPC30, Руководство по эксплуатации

Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды