Endress+Hauser Topclean S CPC30 Скачать руководство пользователя страница 108

Страница: 108 / 178

6 Commissioning

Topclean S

108

Hauser

Instrument check

Display
Keypad
RAM
EEPROM
Flash

Select check
Display

: All the fields are queried alternately. Defective

cells become visible.

Keypad

: All the keys must be pressed one after the other. If

the system is functioning perfectly, the appropriate symbols
appear in the display.

RAM

: "RAM O.K" message if there are no errors.

EEPROM

: "EEPROM O.K" message if there are no errors.

Flash

(memory): "Flash OK" message if there are no errors.

Note!

Leave this item by pressing "PARAM".

DAT download (only available when DAT module is plugged in):

DAT write

DAT read
Erase DAT

DAT selection

DAT write

: You can save both the configuration and the

logs of your transmitter to the DAT module.

DAT read

: Copy the configuration saved on the DAT

module into the EEPROM of the transmitter.

Erase DAT

: Delete all data on the DAT module.

Note!

After the "Read from DAT" copying procedure, a reset is
triggered automatically and the device is configured with
the copied values. (See below for reset).

DAT write:

!!Caution!! All data on the DAT module will be deleted.

Note in display

For safety reasons, you are asked if you really want to
overwrite the existing data.

in progress

Data are written to the DAT module

DAT read:

!!Caution!! All data in Mycom S will be deleted.

Note in display

For safety reasons, you are asked if you really want to
overwrite the existing data of Mycom S.

in progress

Copy

The data from the DAT module are copied to the EEPROM
of the transmitter.

Note!

After the "Read from DAT" copying procedure, a reset is
triggered automatically (similar to a soft reset on a
computer, see below).

Erase DAT:

!!Caution!! All data on the DAT module will be deleted.

Note in display

For safety reasons, you are asked if you really want to delete
the existing data.

in progress

Erase

The data are deleted from the DAT module.

CHOICE
(default = bold)

INFO

Hold

pH 7. 00

Diag

[E]

Check systems

Edit[¯]

Display

Key pad
RAM
EEPROM
Flash

Hold

pH 7. 00

Diag

[E]

DAT

Edit[¯]

DAT write

DAT read
Erase DAT

Содержание Topclean S CPC30



















































































































































































Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды

Endress+Hauser Topclean S CPC30, Руководство по эксплуатации

Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды