Endress+Hauser Topclean S CPC30 Скачать руководство пользователя страница 117

Страница: 117 / 178

Topclean S

6 Commissioning

Hauser

117

Calibration
redox relative

"Calibration absolute"

The transmitter has a calibrated mV display range.

One

absolute mV value is set with a single buffer

solution (adaptation of the measuring chain offset). A buffer solution preferably with 225 or 475 mV
is used.

Accept

Cancel
Repeat calibration

End of calibration

Accept

: Pressing

accepts the new calibration data.

Cancel

: The data are not accepted, the calibration is not repeated.

Repeat calibration

: The data are rejected and a new calibration is started.

Electrode submersed?

Note in display:

Is the electrode back in the medium, so that measurement can take place?

CHOICE
(default = bold)

INFO

CHOICE
(default = bold)

INFO

Calibration with
abs. calibration

Note in display

Display of the type of on-site calibration selected in the calibration settings.

Immerse electrode in buffer

Handling instructions

Immerse the electrode in the buffer.
Confirm by pressing

0225 mV

(–1500 ... +1500 mV)

Enter buffer

Enter the buffer mV value.

Time: 10 s
mV 1:

225

Checks the stability of the calibration

Wait until the measurement is stable:
Time does not count down,
mV value no longer flashes,
Confirm by pressing

Note!

You can set the criteria for the stability check under "

> Setup 1 > Calibration >

Cal. settings".

Invalid calibration value

Note in display:

Error message if the offset is too large.

Offset
Good

0005
mV

Note in display:

Info on electrode
Information on the offset and calibration quality.

Accept

Cancel
Repeat calibration

End of calibration

Accept

: Pressing

accepts the new calibration data.

Cancel

: The data are not accepted, the calibration is not repeated.

Repeat calibration

: The data are rejected and a new calibration is started.

Electrode submersed?

Note in display:

Is the electrode back in the medium, so that measurement can take place?

Содержание Topclean S CPC30



















































































































































































Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды

Endress+Hauser Topclean S CPC30, Руководство по эксплуатации

Результаты поиска

Содержание Topclean S CPC30

Отзывы:

Похожие инструкции для Topclean S CPC30

Бренды по названию

Популярные бренды