Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 21

Страница: 21 / 202

Proline t-mass I 300 HART

Installation

Hauser

Determining dimensions C1 and C2
If only Hauser mounting bosses are used

Mounting boss 1" NPT

C1 + C2 = 112 mm (4.409 in)

Mounting boss G1"

C1 + C2 = 106 mm (4.173 in)

Mounting boss ¾" NPT

C1 + C2 = 108 mm (4.252 in)

Mounting boss G¾"

C1 + C2 = 105 mm (4.134 in)

If a cold/hot tap is used, use dimension "L" →  182 instead of "C1".

Use Applicator to determine dimensions C1 and C2 if using other E+H mounting kits

(e.g. cold/hot taps).

If not exclusively using Hauser mounting bosses

Length of pipe connection used

C2 (compression fitting
with 1" NPT thread)

52 mm (2.047 in)

C2 (compression fitting
with G1" thread)

46 mm (1.811 in)

C2 (compression fitting
with ¾" NPT thread)

48 mm (1.889 in)

C2 (compression fitting
with G¾" thread)

45 mm (1.772 in)

Selecting the length of the insertion version

Select the length of the insertion version using the calculated insertion depth and the

following table. The insertion depth must be within the adjusting range of the insertion

version.

Length of insertion tube

Adjusting range (insertion depth)

[mm]

[in]

[mm]

[in]

235

100 to 235

3.9 to 9.3

335

100 to 335

3.9 to 13.2

435

100 to 435

3.9 to 17.1

608

100 to 608

3.9 to 23.9

Inlet and outlet runs

A fully developed flow profile is a requirement for optimal thermal flow measurement.
To achieve the best possible measuring performance, observe the following inlet and outlet

runs at the very minimum.
• In the case of bidirectional sensors, also observe the recommended inlet run in the

opposite direction.

• If several flow disturbances are present, use flow conditioners.

• Use flow conditioners if it is not possible to observe the required inlet runs.

• In the case of control valves, the amount of disturbance depends on the valve type and

opening degree. The recommended inlet run for control valves is 50 × DN.

• In the case of very light gases (helium, hydrogen), the recommended inlet run must be

doubled.

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды