Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 87

Страница: 87 / 202

Proline t-mass I 300 HART

Commissioning

Hauser

Parameter

Description

Selection

Factory setting

Temperature unit

Select temperature unit.

Unit choose list

Country-specific:
• °C
• °F

Pressure unit

Select process pressure unit.

Unit choose list

Country-specific:
• bar a
• psi a

Velocity unit

Select velocity unit.

Unit choose list

Country-specific:
• m/s
• ft/s

Length unit

Select length unit for nominal diameter.

Unit choose list

Country-specific:
• mm
• in

Date/time format

Select date and time format.

• dd.mm.yy hh:mm
• dd.mm.yy hh:mm am/pm
• mm/dd/yy hh:mm
• mm/dd/yy hh:mm am/pm

–

9.4.7

Displaying the I/O configuration

The

I/O configuration

submenu guides the user systematically through all the parameters

in which the configuration of the I/O modules is displayed.

Navigation

"Setup" menu → I/O configuration

‣

I/O configuration

I/O module 1 to n terminal numbers

→  87

I/O module 1 to n information

→  87

I/O module 1 to n type

→  88

Apply I/O configuration

→  88

I/O alteration code

→  88

Parameter overview with brief description

Parameter

Description

User interface / Selection / User entry

I/O module 1 to n terminal numbers Shows the terminal numbers used by the I/O module.

• Not used
• 26-27 (I/O 1)
• 24-25 (I/O 2)
• 22-23 (I/O 3)

I/O module 1 to n information

Shows information of the plugged I/O module.

• Not plugged
• Invalid
• Not configurable
• Configurable
• HART

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды