Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 60

Страница: 60 / 202

Operation options

Proline t-mass I 300 HART

Hauser

Measuring device: Via CDI-RJ45 service interface

Device

CDI-RJ45 service interface

Measuring device

The measuring device has an RJ45 interface.

Web server

Web server must be enabled; factory setting: ON



For information on enabling the Web server →  64

Measuring device: via WLAN interface

Device

WLAN interface

Measuring device

The measuring device has a WLAN antenna:
• Transmitter with integrated WLAN antenna
• Transmitter with external WLAN antenna

Web server

Web server and WLAN must be enabled; factory setting: ON



For information on enabling the Web server →  64

7.4.3

Establishing a connection

Via service interface (CDI-RJ45)

Preparing the measuring device

1. Depending on the housing version:

Release the securing clamp or securing screw of the housing cover.

2. Depending on the housing version:

Unscrew or open the housing cover.

3. The location of the connection socket depends on the measuring device and the

communication protocol:
Connect the computer to the RJ45 connector via the standard Ethernet connecting

cable .

Configuring the Internet protocol of the computer

The following information refers to the default Ethernet settings of the device.
IP address of the device: 192.168.1.212 (factory setting)

1. Switch on the measuring device.
2. Connect to the computer using a cable →  66.
3. If a 2nd network card is not used, close all the applications on the notebook.

 Applications requiring Internet or a network, such as e-mail, SAP applications,

Internet or Windows Explorer.

4. Close any open Internet browsers.
5. Configure the properties of the Internet protocol (TCP/IP) as defined in the table:

IP address

192.168.1.XXX; for XXX all numerical sequences except: 0, 212 and 255 → e.g.
192.168.1.213

Subnet mask

255.255.255.0

Default gateway

192.168.1.212 or leave cells empty

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды