Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 164

Страница: 164 / 202

Technical data

Proline t-mass I 300 HART

164

Hauser

15.3 Input

Measured variable

Measured process variables

• Mass flow

• Temperature

Calculated process variables

• Corrected volume flow

• Volume flow

• FAD volume flow

• Flow velocity

• Calorific value

• 2nd temperature heat difference

• Heat flow

• Energy flow

• Density

Process variables available for order

Order code for "Sensor version":

• Option SB "Bidirectional" measures the flow in both directions

(»positive« and »negative« flow) and totalizes the flow in both directions. The device is

calibrated in both directions.

• Option SC "Reverse flow detection" only measures the flow in the positive direction. The

reverse flow is detected by the device but is not totalized. The device is only calibrated in

the positive forward flow direction.

Order code for "Application package":

Option EV "Second gas group" enables the configuration of two different standard

gases/gas mixtures in the device and allows the user to switch from one gas group to

another using the status input or (if available) via bus communication.

Measuring range

The available measuring range depends on the choice of gas and size of the pipe. Each

measuring device is calibrated individually with air under reference operating conditions.

No recalibration is required in the case of customer-specific gases, as the device's Gas

Engine functionality converts from air to these gases.
The measuring ranges calibrated for air are indicated in the following section. For

information on other gases and process conditions, contact your sales organization or use

the Applicator selection software.

SI units

• Order code for "Sensor version; sensor; insertion tube", option SA "Unidirectional;

stainless steel; stainless steel"

• Order code for "Sensor version; sensor; insertion tube", option HA "Unidirectional; Alloy;

stainless steel"

[mm]

Full scale value [kg/h]

(Air, 20°C, 1.013 bar a)

Full scale value [Nm3/h]

(Air, 0°C, 1.013 bar a)

Minimum

Maximum

Minimum

Maximum

086

613

100

260

521

150

335

672

200

130

040

101

084

250

204

375

158

757

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды