Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 157

Страница: 157 / 202

Proline t-mass I 300 HART

Repair

Hauser

157

Repair

13.1 General notes

13.1.1 Repair and conversion concept

The Hauser repair and conversion concept provides for the following:

• The measuring devices have a modular design.

• Spare parts are grouped into logical kits with the associated Installation Instructions.

• Repairs are carried out by Hauser Service or by appropriately trained customers.

• Certified devices can only be converted to other certified devices by Hauser

Service or at the factory.

13.1.2 Notes for repair and conversion

For repair and modification of a measuring device, observe the following notes:

‣

Use only original Hauser spare parts.

‣

Carry out the repair according to the Installation Instructions.

‣

Observe the applicable standards, federal/national regulations, Ex documentation (XA)

and certificates.

‣

Document every repair and each conversion and enter them into the

W@M

life cycle

management database.

13.2 Spare parts

W@M Device Viewer

(

www.endress.com/deviceviewer

All the spare parts for the measuring device, along with the order code, are listed here and

can be ordered. If available, users can also download the associated Installation

Instructions.

Measuring device serial number:

• Is located on the nameplate of the device.

• Can be read out via the

Serial number

parameter (→  153) in the

Device

information

submenu.

13.3 Hauser services

Hauser offers a wide range of services.

Your Hauser Sales Center can provide detailed information on the services.

13.4 Return

The requirements for safe device return can vary depending on the device type and

national legislation.

1. Refer to the website for more information:

http://www.endress.com/support/return-material

2. Return the device if repairs or a factory calibration are required, or if the wrong

device was ordered or delivered.

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды