Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 144

Страница: 144 / 202

Diagnostics and troubleshooting

Proline t-mass I 300 HART

144

Hauser

11.5.2 Calling up remedy information

Remedy information is provided for every diagnostic event to ensure that problems can be

rectified quickly:

• On the home page

Remedy information is displayed in a separate field below the diagnostics information.

• In the

Diagnostics

Remedy information can be called up in the working area of the user interface.

The user is in the

Diagnostics

menu.

1. Call up the desired parameter.
2. On the right in the working area, mouse over the parameter.

 A tool tip with remedy information for the diagnostic event appears.

11.6 Adapting the diagnostic information

11.6.1 Adapting the diagnostic behavior

Each item of diagnostic information is assigned a specific diagnostic behavior at the

factory. The user can change this assignment for specific diagnostic information in the

Diagnostic behavior

submenu.

Expert → System → Diagnostic handling → Diagnostic behavior

0723-1

Diagnostic no. 044

/ ../Diagn. behavior

Diagnostic no. 801

Diagnostic no. 274

Warning

A0014048-EN

 41

Taking the example of the local display

You can assign the following options to the diagnostic number as the diagnostic behavior:

Options

Description

Alarm

The device stops measurement. The signal outputs and totalizers assume the defined
alarm condition. A diagnostic message is generated.
The background lighting changes to red.

Warning

The device continues to measure. The signal outputs and totalizers are not affected. A
diagnostic message is generated.

Logbook entry only

The device continues to measure. The diagnostic message is displayed only in the

Event

logbook

submenu (

Event list

submenu) and is not displayed in alternation with the

operational display.

Off

The diagnostic event is ignored, and no diagnostic message is generated or entered.

11.6.2 Adapting the status signal

Each item of diagnostic information is assigned a specific status signal at the factory. The

user can change this assignment for specific diagnostic information in the

Diagnostic

event category

submenu.

Expert → Communication → Diagnostic event category

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды