Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 131

Страница: 131 / 202

Proline t-mass I 300 HART

Operation

Hauser

131

Parameter overview with brief description

Parameter

Description

User interface

Switch status

Shows the current relay switch status.

• Open
• Closed

Switch cycles

Shows number of all performed switch cycles.

Positive integer

Max. switch cycles number

Shows the maximal number of guaranteed switch cycles.

Positive integer

10.5 Adapting the measuring device to the process

conditions

The following are available for this purpose:

• Basic settings using the

Setup

menu (→  77)

• Advanced settings using the

Advanced setup

submenu (→  103)

10.6 Performing a totalizer reset

The totalizers are reset in the

Operation

submenu:

• Control Totalizer

• Reset all totalizers

Navigation

"Operation" menu → Totalizer handling

‣

Totalizer handling

Control Totalizer 1 to n

→  131

Preset value 1 to n

→  131

Reset all totalizers

→  131

Parameter overview with brief description

Parameter

Prerequisite

Description

Selection / User entry

Control Totalizer 1 to n

A process variable is selected in the

Assign process variable

parameter

(→  104) of the

Totalizer 1 to n

submenu.

Control totalizer value.

• Totalize
• Reset + hold
• hold
• Reset + totalize
• totalize
• Hold

Preset value 1 to n

A process variable is selected in the

Assign process variable

parameter

(→  104) of the

Totalizer 1 to n

submenu.

Specify start value for totalizer.

Dependency



The unit of the selected process
variable is specified for the
totalizer in the

Unit totalizer

parameter (→  104).

Signed floating-point
number

Reset all totalizers

–

Reset all totalizers to 0 and start.

• Cancel
• Reset + totalize

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды