Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 202

background image

Installation

Proline t-mass I 300 HART

20

Hauser

Pipes
The measuring device must be professionally installed, and the following points must

be observed:

• Weld pipes professionally.

• Use seals of the correct size.

• Align flanges and seals correctly.

• Remove protection cap from sensing element.
• Following installation, the pipe must be free from dirt and particles in order to avoid

damage to the sensors.

• For further information → ISO standard 14511.

Sensor selection and arrangement

The minimum length of the sensor can be determined using the Hauser

Applicator program (version 10.00 or higher) or with the calculation formula below.
The minimum length of the sensor is determined by the necessary insertion depth. The

calculated necessary insertion depth must be within the adjusting range of the selected

insertion version.

Insertion depth

The minimum length of the insertion version can be determined using the Hauser

Applicator program or with the calculation formula below. The calculated necessary

insertion depth must be within the adjusting range of the selected insertion version.

NOTICE

Metal ferrules undergo plastic deformation during the initial installation.

As a result the insertion depth is fixed after initial installation and the ferrules can no

longer be replaced.

‣

Pay attention to information on preconditions and on determining the insertion depth.

‣

Check the insertion depth closely before tightening the ferrules.

A

B

C2

C1

A

B

C2

C1

230

220

210

200

190

180

9

8

7

230

220

210

200

190

180

9

8

7

230

220

210

200

190

180

9

8

7

A0039548

 3

Determine the dimensions A, B, C1 and C2

A

In the case of a circular pipe: the pipe internal diameter (DN); in the case of a duct: the inner dimension

B

Thickness of pipe wall or of duct wall

C1 Mounting kit
C2 Sensor's compression fitting

Calculating the insertion depth

Insertion depth = (0.3⋅ A) + B + (C1 + C2)

The insertion depth must be at least 100mm.

«
...
18
19
20
21
22
...
»

Содержание HART Proline t-mass I 300











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HART Proline t-mass I 300

Charge Analyzer 711

Бренд: 3M Страницы: 24

Бренд: DAE Страницы: 28

NANOCOLOR UV/VIS II

Бренд: Macherey-Nagel Страницы: 99

Бренд: YOKOGAWA Страницы: 53

Бренд: KBR Страницы: 12

Pasport PS-2138

Бренд: Pasco Scientific Страницы: 26

Бренд: WIKA Страницы: 88

Бренд: PASI Страницы: 59

Бренд: Lutron Electronics Страницы: 10

Бренд: CryptOn Страницы: 13

Бренд: Kinesys Страницы: 10

Бренд: REED Страницы: 20

Бренд: Hanna Страницы: 44

Бренд: Hauber Elektronik Страницы: 28

Бренд: Fungilab Страницы: 47

Бренд: Keysight Страницы: 26

Superstatic 749

Бренд: Sontex Страницы: 24

CA67 concert artist

Бренд: Kawai Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды