Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 176

Страница: 176 / 202

Technical data

Proline t-mass I 300 HART

176

Hauser

15.6 Performance characteristics

Reference operating

conditions

• Error limits based on ISO 11631

• Dry air with +20 to +30 °C (+68 to +86 °F) at 0.8 to 1.5 bar (12 to 22 psi)

• Specifications as per calibration protocol

• Accuracy based on accredited calibration rigs that are traced to ISO 17025.

To obtain measured errors, use the

Applicator

sizing tool →  161

Maximum measured error

[% kg/h]

±10

[%]

100

±5

120

140

[% lb/h]

160

180

200

A0042739

Calibrated measuring range

The measuring accuracy is specified in relation to the mass flow and divided into two

ranges:

• ±1.0 % of the current measured value for 100% to 10% of the calibrated measuring

range (under reference operating conditions)

• ±0.10 % of the calibrated full scale value for 10% to 1% of the calibrated measuring

range (under reference operating conditions)

The measuring device is calibrated and adjusted on an accredited and traceable calibration

rig and its accuracy is certified in a calibration report

(5 control points).

Order code for "Calibration flow":

• Option G "Factory calibration": calibration report (5 control points)

• Option K "Traceable ISO/IEC17025": Swiss Calibration Services (SCS) calibration report (5

control points) which confirms traceability to the national calibration standard

For information on calibrated measuring ranges and maximum full scale values

→  164

Extended measuring range

The device has an extended measuring range that goes beyond the maximum calibrated

value (100%). Here, the last measured values in the calibrated range are taken and then

extrapolated. The end of the extrapolated range is only reached once the productive

energy of the sensor is exceeded and/or the Mach number is greater than listed below.

Mach

number

Order code

0.2

• Order code for "Sensor version; sensor; insertion tube:", option SB "Bidirectional; stainless steel;

stainless steel"

• Order code for "Sensor version; sensor; insertion tube:", option SC "Reverse flow detection;

stainless steel; stainless steel"

0.4

• Order code for "Sensor version; sensor; insertion tube:", option SA "Unidirectional; stainless

steel; stainless steel"

• Order code for "Sensor version; sensor; insertion tube:", option HA "Unidirectional; Alloy;

stainless steel"

Two calibration reports for the order code for "Sensor version; sensor; insertion tube:", option SB "Bidirectional; stainless steel; stainless steel"

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды