Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 74

Страница: 74 / 202

System integration

Proline t-mass I 300 HART

Hauser

Assignment

Device variables

Temperature

Totalizer 1

Totalizer 2

Totalizer 3

8.3

Other settings

Burst mode functionality in accordance with HART 7 Specification:

Navigation

"Expert" menu → Communication → HART output → Burst configuration → Burst

configuration 1 to n

‣

Burst configuration

‣

Burst configuration 1 to n

Parameter overview with brief description

Parameter

Description

Selection / User entry

Burst mode 1 to n

Activate the HART burst mode for burst message X.

• Off
• On

Burst command 1 to n

Select the HART command that is sent to the HART master.

• Command 1
• Command 2
• Command 3
• Command 9
• Command 33
• Command 48

Burst variable 0

For HART command 9 and 33: select the HART device variable
or the process variable.

• Mass flow
• Corrected volume flow
• FAD volume flow

• Volume flow
• Temperature
• Density
• Flow velocity
• Pressure
• Energy flow

• Heat flow

• 2nd temperature delta heat

• Electronic temperature
• Totalizer 1
• Totalizer 2
• Totalizer 3
• Percent of range
• Measured current
• Current input 1

• Current input 2

• Current input 3

• Primary variable (PV)
• Secondary variable (SV)
• Tertiary variable (TV)
• Quaternary variable (QV)
• HART input
• Not used

Burst variable 1

For HART command 9 and 33: select the HART device variable
or the process variable.

See the

Burst variable 0

parameter.

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды