Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 33

Страница: 33 / 202

Proline t-mass I 300 HART

Electrical connection

Hauser

Electrical connection

NOTICE

The measuring device does not have an internal circuit breaker.

‣

For this reason, assign the measuring device a switch or power-circuit breaker so that

the power supply line can be easily disconnected from the mains.

‣

Although the measuring device is equipped with a fuse, additional overcurrent

protection (maximum 10 A) should be integrated into the system installation.

6.1

Electrical safety

In accordance with applicable federal/national regulations.

6.2

Connection conditions

6.2.1

Required tools

• For cable entries: Use corresponding tools

• For securing clamp: Allen key 3 mm

• Wire stripper

• When using stranded cables: Crimper for wire end ferrule

• For removing cables from terminal: Flat blade screwdriver ≤ 3 mm (0.12 in)

6.2.2

Requirements for connecting cable

The connecting cables provided by the customer must fulfill the following requirements.

Protective grounding cable for the outer ground terminal

Conductor cross-section ≤2.08 mm

(14 AWG)

Grounding impedance must be less than 2 Ω.

Permitted temperature range

• The installation guidelines that apply in the country of installation must be observed.

• The cables must be suitable for the minimum and maximum temperatures to be

expected.

Power supply cable (incl. conductor for the inner ground terminal)

Standard installation cable is sufficient.

Signal cable

Current output 4 to 20 mA HART

A shielded cable is recommended. Observe grounding concept of the plant.

Current output 0/4 to 20 mA

Standard installation cable is sufficient.

Pulse/frequency/switch output

Standard installation cable is sufficient.

Relay output

Standard installation cable is sufficient.

Содержание HART Proline t-mass I 300











































































































































































































Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline t-mass I 300, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline t-mass I 300

Отзывы:

Похожие инструкции для HART Proline t-mass I 300

Бренды по названию

Популярные бренды