manualshive.com logo in svg

Daikin RMXS-L Series, Руководство по обслуживанию

Daikin RMXS-L Series - мощная и надежная система кондиционирования воздуха для вашего дома или офиса. Просто загрузите бесплатный сервисный мануал для этой модели с manualshive.com, чтобы получить подробные инструкции по эксплуатации и обслуживанию. Теперь ваш климат контроль находится под вашим полным контролем.

Поделиться
Скачать
background image

SiUS181305E

137

Troubleshooting

7.7

Discharge Pipe Temperature Abnormality ............................................... 188

7.8

Refrigerant Overcharged.......................................................................... 189

7.9

Outdoor Temperature Thermistor (R1T) Abnormality .............................. 190

7.10 Discharge Pipe Thermistor (R2T) Abnormality......................................... 191
7.11 Suction Pipe Thermistor (R3T, R5T) Abnormality .................................... 192
7.12 Outdoor Heat Exchanger Thermistor (R4T) Abnormality ......................... 193
7.13 Outdoor Liquid Pipe Thermistor (R7T) Abnormality ................................. 194
7.14 Subcooling Heat Exchanger Gas Pipe Thermistor (R6T) Abnormality..... 195
7.15 High Pressure Sensor Abnormality .......................................................... 196
7.16 Low Pressure Sensor Abnormality ........................................................... 197
7.17 Outdoor Unit PCB Abnormality................................................................. 198
7.18 Radiation Fin Temperature Rise .............................................................. 199
7.19 Inverter Compressor Abnormality............................................................. 200
7.20 Inverter Current Abnormality .................................................................... 201
7.21 Compressor Start-up Error ....................................................................... 202
7.22 High Voltage of Capacitor in Main Inverter Circuit ................................... 203
7.23 Radiation Fin Thermistor Abnormality ...................................................... 204
7.24 Low Pressure Drop due to Refrigerant Shortage or Electronic Expansion 

Valve Abnormality .................................................................................... 205

7.25 Power Supply Insufficient or Instantaneous Failure ................................. 207
7.26 Check Operation is not Conducted .......................................................... 208
7.27 Signal transmission Error between Indoor Unit and Outdoor Unit in the Same 

System ..................................................................................................... 209

7.28 Excessive Number of Indoor Units ........................................................... 210
7.29 Address Duplication of Central Remote Controller................................... 211
7.30 Transmission Error between Centralized Remote Controller and Indoor            

Unit ........................................................................................................... 212

7.31 System is not Set yet................................................................................ 214
7.32 System Abnormality, Refrigerant System Address Undefined ................. 215
7.33 Check for Outdoor Unit............................................................................. 216

8. Thermistor Resistance / Temperature Characteristics ............................220
9. Pressure Sensor .....................................................................................222
10.Method of Replacing Inverter’s Power Transistors Modules ...................223

Содержание RMXS-L Series



























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RMXS-L Series

Gardena 1732 Operating Instructions Manual preview
1732
Бренд: Gardena Страницы: 17
Daikin C-Series Operation Manual preview
C-Series
Бренд: Daikin Страницы: 27
Uberhaus 1820 Owner'S Manual preview
1820
Бренд: Uberhaus Страницы: 19
EBARA GP Operating And Maintenance Manual preview
GP
Бренд: EBARA Страницы: 164
Zehnder Rittling ComfoClime 24 Quick User Manual preview
ComfoClime 24
Бренд: Zehnder Rittling Страницы: 4
B+BTec VAC 800 Translation Of The Original Instructions preview
VAC 800
Бренд: B+BTec Страницы: 20
ICP PHM324K00A1 Installation Instructions Manual preview
PHM324K00A1
Бренд: ICP Страницы: 14
kayami ECH Series Manual preview
ECH Series
Бренд: kayami Страницы: 28
Daikin EKHH2E-AV3 Installation And User Manual preview
EKHH2E-AV3
Бренд: Daikin Страницы: 40
Pro-Elec PEL00915 Manual preview
PEL00915
Бренд: Pro-Elec Страницы: 4
Malmbergs 88 792 62 Instruction Manual preview
88 792 62
Бренд: Malmbergs Страницы: 12
salmson NOEH Installation And Operating Instructions Manual preview
NOEH
Бренд: salmson Страницы: 48
Reece Kado Lussi Series Installation Instructions preview
Kado Lussi Series
Бренд: Reece Страницы: 3
Varian TV 1001 SEM Instruction Manual preview
TV 1001 SEM
Бренд: Varian Страницы: 53
Wacker Neuson 0009112 Operator'S Manual preview
0009112
Бренд: Wacker Neuson Страницы: 60
KC 23.580 Manual preview
23.580
Бренд: KC Страницы: 11
BUSCH COBRA NC 0500 B Instruction Manual preview
COBRA NC 0500 B
Бренд: BUSCH Страницы: 36
purline HOTI M52 User Manual preview
HOTI M52
Бренд: purline Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды