Daikin RMXS-L Series Скачать руководство пользователя страница 202 | Manualshive

Страница: 202 / 250

background image

Troubleshooting for Outdoor Unit

SiUS181305E

193

Troubleshooting

7.8

Refrigerant Overcharged

Error Code

F6

Method of Error
Detection

Excessive charging of refrigerant is detected during check operation by using outdoor temperature,
outdoor heat exchanger temperature, and liquid pipe temperature.

Error Decision
Conditions

When the amount of refrigerant, which is calculated during check operation by using outdoor
temperature, outdoor heat exchanger temperature, and liquid pipe temperature, exceeds the
standard.

Supposed
Causes



Refrigerant overcharge



Incorrect installation of outdoor temperature thermistor, outdoor heat exchanger thermistor,
liquid pipe thermistor (R1T, R4T, R7T)



Defective outdoor temperature thermistor, outdoor heat exchanger thermistor, liquid pipe
thermistor (R1T, R4T, R7T)

Troubleshooting

Refer to Thermistor Resistance / Temperature Characteristics table 1 on page 224.

Remove the outdoor
temperature thermistor,
outdoor heat exchanger
thermistor, liquid pipe
thermistor from the outdoor
PCB and measure the
resistance with a tester.

Check the mounting condition
of the outdoor temperature
thermistor, outdoor heat
exchanger thermistor, liquid
pipe thermistor.

Are the thermistors

installed on pipes

correctly?

Is the

characteristic of the

thermistors normal?

Correct the amount of
refrigerant.

(R13024)

Install the thermistor
correctly.

NO

Replace the defective
thermistor.

NO

YES

YES

Caution

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

«
...
200
201
202
203
204
...
»

Содержание RMXS-L Series



























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RMXS-L Series

Бренд: Makita Страницы: 96

Бренд: Eastern Tabletop Страницы: 19

Altherma 3 R F+W

Бренд: Daikin Страницы: 20

Бренд: Dex Страницы: 24

Бренд: Enerpac Страницы: 40

Бренд: Bionaire Страницы: 8

Бренд: VonHaus Страницы: 10

Aeromax Piscine 10

Бренд: Thermor Страницы: 32

Бренд: Maktek Страницы: 27

Бренд: nedis Страницы: 60

Бренд: iGenix Страницы: 9

BioPressure II 6000

Бренд: ubbink Страницы: 64

Бренд: Wacker Neuson Страницы: 52

Бренд: ProMinent Страницы: 124

Бренд: Daikin Страницы: 44

Бренд: Gabarron Страницы: 8

Taro Pumps NCH 2250

Бренд: Texmo Industries Страницы: 34

Бренд: S&P Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды