Daikin RMXS-L Series Скачать руководство пользователя страница 229

Страница: 229 / 250

SiUS181305E

Troubleshooting for Outdoor Unit

Troubleshooting

220

7.33 Check for Outdoor Unit

7.33.1 Check for Causes of Rise in High Pressure

Check No.30

Referring to the Fault Tree Analysis (FTA) shown below, probe the faulty points.

A temperature

difference in excess of

C (18

F) between

the inlet and the outlet

is deemed to be

abnormal.

Short-circuit

Rise in high
pressure

Local
pressure
rise

High pipe
resistance

Stop valve closed

Bent or crashed pipe

Clogging of foreign
particles

←

Check to be sure the stop valve is open.

←

Conduct visual checks for pipe conditions.

←

Is there any temperature difference caused

before and after the filter or branch pipe?

If the outdoor unit
electronic
expansion valve is
throttled: (See

∗

1.)

Faulty outdoor
unit electronic
expansion valve

Faulty valve coil

Faulty valve body

←

Are the coil resistance and insulation normal?

Faulty
control

Faulty high pressure
sensor

Faulty control PCB

←

Are the electrical characteristics normal?

←

Is the pressure value checked with the

Service Checker corresponding to the
measurement of the pressure sensor?

Faulty
high
pressure
control

In cooling

High suction
air
temperature
of the
condenser

In heating

High suction air
temperature
of outdoor unit

Short-circuit

High ambient
temperature

←

Is the suction air temperature not more than

C (114.8

F)?

←

Is the outdoor temperature not more than

C (114.8

F)?

High suction
air temperature
of indoor unit

High ambient
temperature

←

Is the suction air temperature not more than

C (80.6

F)?

←

Is the indoor temperature not more than

C (80.6

F)?

Faulty suction air thermistor of indoor unit

High suction air temperature of outdoor unit

Faulty outdoor temperature thermistor of outdoor unit

←

Is the connector properly connected?

Are the thermistor resistance characteristics normal?

←

Is the outdoor temperature not more than

CWB (60.8

FWB)?

←

Is the connector properly connected?

Are the thermistor resistance characteristics normal?

Dirty condenser

Mixing of non-condensable gas

←

Is the heat exchanger clogged? (In cooling)

←

Is air or else mixed in the refrigerant system?

Decreased
fan airflow
rate

←

Can the fan motor be rotated with hands?

Are the motor coil resistance and
insulation normal?

←

If a spare PCB is mounted, is the capacity

setting properly made?

Faulty control
PCB
(Including
capacity setting)

High air
passage
resistance

Dirty filter

←

Is the air filter clogged?

Obstacle

←

Is there any obstacle in the air passage?

Excessive refrigerant charging

Improper model selection

In heating

←

Refer to troubleshooting

←

Is the indoor unit too small compared to

the large-sized outdoor unit?

∗

1: In cooling, it is normal if the outdoor unit electronic expansion valve (Y1E) is fully open.

(R19097)

Degradation
in condensing
capacity

Decreased
fan
output

Faulty fan
motor

Содержание RMXS-L Series



























































































































































































































































Результаты поиска

Содержание RMXS-L Series

Отзывы:

Похожие инструкции для RMXS-L Series

Бренды по названию

Популярные бренды

Daikin RMXS-L Series, Руководство по обслуживанию

Результаты поиска

Содержание RMXS-L Series

Отзывы:

Похожие инструкции для RMXS-L Series

Бренды по названию

Популярные бренды