manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 98

INS_CWGE24MS2_REV–

10/05/16     PAGE 98

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Notice: The maximum VLAN group is 4094.

CLI Configuration

Node

Command

Description

enable

show vlan VLANID

This command displays the VLAN configurations.

configure

vlan <1~4094>

This command enables a VLAN and enters the VLAN node.

configure

no vlan <1~4094>

This command deletes a VLAN.

vlan

show

This command displays the current VLAN configurations.

vlan

name STRING

This command assigns a name for the specific VLAN.
The VLAN name should be the combination of the digit or the 
alphabet or hyphens (-) or underscores (_).
The maximum length of the name is 16 characters.

vlan

no name

This command configures the vlan name to default.
Note: The default vlan name is “VLAN”+vlan_ID, VLAN1, VLAN2,…

vlan

add PORTLISTS

This command adds a port or a range of ports to the vlan.

vlan

fixed PORTLISTS

This command assigns ports for permanent member of the vlan.

vlan

no fixed PORTLISTS

This command removes all fixed member from the vlan.

vlan

tagged PORTLISTS

This command assigns ports for tagged member of the VLAN group. 
The ports should be one/some of the permanent members of the vlan.

vlan

no tagged PORTLISTS This command removes all tagged member from the vlan.

vlan

untagged PORTLISTS This command assigns ports for untagged member of the VLAN 

group. The ports should be one/some of the permanent members of 
the vlan.

vlan

no untagged 
PORTLISTS

This command removes all untagged member from the vlan.

interface

acceptable frame type 
(all|tagged|untagged)

This command configures the acceptable frame type.
all      - acceptable all frame types.
tagged   - acceptable tagged frame only.
untagged – acceptable untagged frame only.

interface

pvid VLANID

This command configures a VLAN ID for the port default VLAN ID.

interface

no pvid

This command configures 1 for the port default VLAN ID.

configure

interface range 
gigabitethernet1/0/ 
PORTLISTS

This command enters the interface configure node.

if-range

pvid VLANID

This command configures a VLAN ID for the port default VLAN ID.

if-range

no pvid

This command configures 1 for the port default VLAN ID.

configure

vlan range STRINGS

This command configures a range of vlans.

configure

no vlan range STRINGSThis command removes a range of vlans.

vlan-range add PORTLISTS

This command adds a port or a range of ports to the vlans.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды