manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 278

INS_CWGE24MS2_REV–

10/05/16     PAGE 278

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

User Account

Introduction

The Switch allows users to create up to 6 user account. The user name and the password should 
be the combination of the digit or the alphabet. The last admin user account cannot be deleted. 
Users should input a valid user account to login the CLI or web management.

User Authority:

The Switch supports two types of the user account, admin and normal. The default user’s account 
is username (admin) / password (admin).

 

» admin 

- 

read / write.

 

» normal  - 

read only.  

; Cannot enter the privileged mode in CLI. 
; Cannot apply any configurations in web.

Default Settings

Maximum user account 

 

: 6.

Maximum user name length 

 

: 32.

Maximum password length 

 

: 32.

Default user account for privileged mode  : admin / admin.

Notices

The Switch allows users to create up to 6 user account.

The user name and the password should be the combination of the digit or the alphabet.

The last admin user account cannot be deleted.

The maximum length of the username and password is 32 characters.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды