Comnet CWGE24MS2 Скачать руководство пользователя страница 163

Страница: 163 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 163

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

CLI Configuration

Node

Command

Description

enable

show pppoe intermediate-
agent configuration

This command displays the current configurations for the
PPPoE IA.

enable

show pppoe intermediate-
agent statistics

This command displays the current statistics for the PPPoE IA.

enable

show pppoe intermediate-
agent statistics by-vlan
<VLAN-list>

This command displays the current statistics by specific VLANs
for the PPPoE IA.

configure

clear pppoe intermediate-
agent statistics

This command clears the statistics for the PPPoE IA.

configure

clear pppoe intermediate-
agent statistics by-vlan
<VLAN-list>

This command clears the statistics by specific VLANs for the
PPPoE IA.

configure

pppoe intermediate-agent
<enable|disable>

This command disables / enables the PPPoE IA on the switch.

configure

pppoe intermediate-agent
format-type user-defined
<user-defined-string>

This command configures the user defined circuit ID string for
the PPPoE IA.

configure

pppoe intermediate-agent
vlan <VLAN-list>

This command enables the PPPoE IA on either (a) a specific
VLAN, (b) a comma separated list like “x,y,” or (c) a range like
“x-y”.

configure

pppoe intermediate-agent
circuit-id-vlan <VLAN-list>

This command enables the PPPoE IA circuit-id on either (a)
a specific VLAN, (b) a comma separated list like “x,y,” or (c) a
range like “x-y”.

configure

pppoe intermediate-agent
remote-id-vlan <VLAN-list>

This command enables the PPPoE IA remote-id on either (a)
a specific VLAN, (b) a comma separated list like “x,y,” or (c) a
range like “x-y”.

configure

no pppoe intermediate-agent
format-type user-defined

This no command removes the user defined circuit ID for the
PPPoE IA.

configure

no pppoe intermediate-agent
vlan

This no command disables PPPoE IA on all VLANs.

configure

no pppoe intermediate-agent
vlan <VLAN-list>

This no command disables the PPPoE IA on specific VLANs.

configure

no pppoe intermediate-agent
circuit-id-vlan

This no command disables the PPPoE IA circuit-id on all VLANs.

configure

no pppoe intermediate-agent
circuit-id-vlan <VLAN-list>

This no command disables the PPPoE IA circuit-id on specific
VLANs.

configure

no pppoe intermediate-agent
remote-id-vlan

This no command disables the PPPoE IA remote-id on all
VLANs.

configure

no pppoe intermediate-agent
remote-id-vlan <VLAN-list>

This no command disables the PPPoE IA remote-id on specific
VLANs.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды