manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 92

INS_CWGE24MS2_REV–

10/05/16     PAGE 92

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Explicit Host Tracking

This capability enables the Switch to track each individual host that is joined to a particular group 
or channel and to achieve minimal leave latencies when hosts leave a multicast group or channel.

Notice:

Before configuring the ip igmp explicit-tracking command, IGMP must be enabled.

When explicit host tracking is enabled, the router uses more memory than if explicit tracking is 

disabled because the router must store the membership state of all hosts on the interface.

CLI Configurations

Node

Command

Description

enable

show ip multicast

This command shows the IGMP snooping 
membership information.

enable

show igmp-snooping membership

This command shows the IGMP snooping host 
membership information.

configure igmp-snooping explicit-tracking

This command enables the IGMP snooping 
explicit host tracking on the Switch.

configure no igmp-snooping explicit-tracking

This command disables the IGMP snooping 
explicit host tracking on the Switch.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды