Comnet CWGE24MS2 Скачать руководство пользователя страница 139

Страница: 139 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 139

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

CLI Configuration

Node

Command

Description

enable

show erps

This command displays the ERPS configurations.

enable

show erps instance

This command displays the ERPS instance configurations.

enable

show erps instance
INSTANCE_ID

This command displays the specific ERPS instance configurations.

configure

erps enable

This command enables the global ERPS on the Switch.

configure

no erps enable

This command disables the global ERPS on the Switch.

configure

erps ring-id VALUE

This command creates an ERPS ring and its ID and enter ERPS
node.

configure

erps instance

This command enters the instance configure node.

configure

no erps ring-id VALUE

This command creates an ERPS ring and enter ERPS node to
configure detail ring configurations.

erps-ring

show

This command displays the configurations of the ring.

erps-ring

control-vlan

This command configures a control-vlan for the ERPS ring.

erps-ring

guard-timer

This command configures the Guard Timer for the ERPS ring.
(default:500ms)

erps-ring

holdoff-timer

This command configures the Hold-off Timer for the ERPS ring.
(default:0 ms)

erps-ring

left-port PORTID type
[owner|neighbor|normal]

This command configures the left port and type for the ERPS ring.

erps-ring

mel VALUE

This command configures a Control MEL for the ERPS ring.

erps-ring

name STRING

This command configures a name for the ERPS ring.

erps-ring

revertive

This command configures the revertive mode for the ERPS ring.

erps-ring

no revertive

This command configures the non-revertive mode for the ERPS
ring.

erps-ring

right-port PORTID type
[owner|neighbor|normal]

This command configures the right port and type for the ERPS ring.

erps-ring

ring enable

This command enables the ring.

erps-ring

no ring enable

This command disables the ring.

erps-ring

version

This command configures a version for the ERPS ring.

erps-ring

wtr-timer

This command configures the WTR Timer for the ERPS ring.
(default: 5 minutes)

config-erps-
inst

instance INSTANCE_ID
control-vlan VLAN_ID
data-vlan VLAN_ID

This command configures a new instance and specifies its control
vlan and data vlan.

config-erps-
inst

no instance INSTANCE_
ID

This command removes an instance.

config-erps-
inst

show

This command displays all of the instance configurations.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды