manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 164

INS_CWGE24MS2_REV–

10/05/16     PAGE 164

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Node

Command

Description

interface

pppoe intermediate-agent 
<enable|disable>

This command disables / enables the PPPoE IA on specific 
interface for the PPPoE IA.

interface

pppoe intermediate-agent 
trust

This command sets a physical interface as trusted port.

interface

pppoe intermediate-agent 
format-type <circuit-
id|remote-id> <id-string>

This command sets circuit ID or remote ID string on specific 
interface for the PPPoE IA.

interface

pppoe intermediate-
agent vendor-tag 
<keep|replace|strip>

This command is used to set the retransmitting policy of the 
specific interface for the PADO/PADS packet.
Default:Keep

interface

pppoe intermediate-agent 
vlan <VLAN-list>

This command enables the PPPoE IA on specific VLANs of 
interface.

interface

no pppoe intermediate-agent 
trust

This command sets a physical interface as untrusted port.

interface

no pppoe intermediate-
agent format-type <circuit-
id|remote-id>

This command removes circuit ID or remote ID string on 
specific interface for the PPPoE IA

interface

no pppoe intermediate-agent 
vendor-tag

The command sets the retransmitting policy of the specific 
interface as “keep”. 

interface

no pppoe intermediate-agent 
vlan

This command disables the PPPoE IA on all VLANs.

interface

no pppoe intermediate-agent 
vlan <VLAN-list>

This command disables the PPPoE IA on specific VLANs of 
interface.

if-pppoe-
vlan

pppoe intermediate-agent 
format-type <circuit-
id|remote-id> <id-string>

This command sets circuit ID or remote ID string on specific 
VLANs of interface for the PPPoE IA.

if-pppoe-
vlan

no pppoe intermediate-
agent format-type <circuit-
id|remote-id>

This command removes circuit ID or remote ID string on 
specific VLANs of interface for the PPPoE IA.

Example:

  CWGE24MS2(config)#pppoe intermediate-agent enable
  CWGE24MS2(config)#pppoe intermediate-agent vlan 1-100,200,300
  CWGE24MS2(config)#pppoe intermediate-agent circuit-id-vlan 1-100,200,300
  CWGE24MS2(config)#pppoe intermediate-agent remote-id-vlan 1-100,200,300
  CWGE24MS2(config)#pppoe intermediate-agent format-type user-defined %H%SPACE+atm+
%SPACE+/0/0/+%PORT+:+%CVLAN
  CWGE24MS2(config)#interface 1/0/1
CWGE24MS2(config-if)#pppoe intermediate-agent enable
CWGE24MS2(config-if)#interface 1/0/8
CWGE24MS2(config-if)#pppoe intermediate-agent enable
CWGE24MS2(config-if)#pppoe intermediate-agent trust
CWGE24MS2(config-if)#pppoe intermediate-agent vlan 1
CWGE24MS2(if-pppoe-vlan)#

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды