Comnet CWGE24MS2 Скачать руководство пользователя страница 79

Страница: 79 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 79

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

IGMP Snooping Filtering

The IGMP Snooping Filter allows users to configure one or some of range or multicast address to
drop or to forward them.

CLI Configurations

Node

Command

Description

enable

show igmp-snooping
filtering

This command displays the IGMP snooping filtering
configurations.

configure

igmp-snooping filtering
(enable|disable)

This command enables/disables the IGMP snooping filtering
profiles on the Switch.

configure

igmp-snooping filtering
profile

This command enters the IGMP snooping filtering profiles
configuration node.

configure

no igmp-snooping
filtering all

This command removes all of the IGMP snooping filtering
profiles from the Switch.

configure

no igmp-snooping
filtering STRINGS

This command removes the IGMP snooping filtering profiles by
name from the Switch.

config-igmp

Group GROUP_ID start-
address START-ADDR
end-address END-ADDR

This command configures the group configurations, including
group index and start multicast address and end multicast
address.

config-igmp

type (deny|permit)

This command configures the type of deny or permit for the
group.

config-igmp

no group GROUP-ID

This command removes the group configurations.

config-igmp

no group all

This command removes all of the group configurations.

config-igmp

type (deny|permit)

This command configures the type of deny or permit for the
group.

interface

igmp-snooping filtering
profile STRING

This command enables the IGMP snooping filtering profiles on
the specific port.

interface

no igmp-snooping
filtering profile STRINGS

This command disables the IGMP snooping filtering profiles on
the specific port.

configure

interface range
gigabitethernet1/0/
PORTLISTS

This command enters the interface configure node.

if-config

igmp-snooping filtering
profile STRING

This command enables the IGMP snooping filtering profiles on
the range of ports.

if-config

no igmp-snooping
filtering profile STRINGS

This command disables the IGMP snooping filtering profiles on
the range of ports.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды