manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 36

INS_CWGE24MS2_REV–

10/05/16     PAGE 36

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Management Host

Introduction

The feature limits the hosts which can manage the Switch. That is, any hosts can manage the 
Switch via telnet or web browser. If the user has configured one or more management hosts,  
the Switch can be managed by these hosts only. The feature allows the user to configure up to  
3 management IP host entries.

Default Settings

The default is none, any host can manage the Switch via telnet or web browser.

CLI Configuration

Node

Command

Description

enable

show interface eth0

The command displays the all of the interface eth0 configurations.

eth0

show

The command displays the all of the interface eth0 configurations.

eth0

management host 
A.B.C.D

The command adds a management host address.

eth0

no management host 
A.B.C.D

The command deletes a management host address.

Example:

CWGE24MS2#configure terminal

CWGE24MS2(config)#interface eth0

CWGE24MS2(config-if)#management host 192.168.200.106

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды