manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 6

INS_CWGE24MS2_REV–

10/05/16     PAGE 6

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

FCC Warning

This equipment has been tested and found to comply with the limits for a class A device, pursuant 
to part 15 of FCC rules. These limits are designed to provide reasonable protection against 
harmful interference in a commercial installation. This equipment generates uses and can radiate 
radio frequency energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communication. Operation of this equipment in a residential 
area is likely to cause harmful interference, in which case, the user will be required to correct the 
interference at the user’s own expense.

CE

This is a Class A product. In a domestic environment, this product may cause radio interference in 
which case the user may be required to take adequate measures.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды