manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 249

INS_CWGE24MS2_REV–

10/05/16     PAGE 249

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Traffic Monitor

Introduction

The function can be enabled / disabled on a specific port or globally be enabled disabled on the 
Switch.

The function will monitor the broadcast / multicast / broadcast and multicast packets rate. If the 
packet rate is over the user’s specification, the port will be blocked. And if the recovery function is 
enabled, the port will be enabled after recovery time.

Default Settings

   Packet 

 Packet 

Recovery

Port   

State       Status     Type 

Rate(pps)  State 

Time(min)

----   

--------   

-------   

-----------    ---------    --------   

---------

 1     

Disabled   Normal     Bcast       1000   

Enabled  1

 2     

Disabled   Normal     Bcast   

1000   

Enabled  1

 3     

Disabled   Normal     Bcast  

1000    

Enabled  1

 4     

Disabled   Normal     Bcast    

1000   

Enabled  1

 5     

Disabled   Normal     Bcast    

1000   

Enabled  1

 6     

Disabled   Normal     Bcast    

1000   

Enabled  1

  . . . . . . . . .

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды