Comnet CWGE24MS2 Скачать руководство пользователя страница 179

Страница: 179 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 179

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Node

Command

Description

interface

no spanning-tree port-
priority

This command configures the port priority to default for the specific
port.

configure interface range

gigabitethernet1/0/
PORTLISTS

This command enters the interface configure node.

if-range

spanning-tree
(disable|enable)

This command configures enables/disables the STP function for the
specific port.

if-range

spanning-
tree bpdufilter
(disable|enable)

This command configures enables/disables the bpdufilter function for
the specific port.

if-range

spanning-tree
bpduguard
(disable|enable)

This command configures enables/disables the bpduguard function for
the specific port.

if-range

spanning-
tree rootguard
(disable|enable)

This command enables/disables the BPDU Root guard port setting for
the specific port.

if-range

spanning-tree edge-
port (disable|enable)

This command enables/disables the edge port setting for the specific
port.

if-range

spanning-tree cost
VALUE

This command configures the cost for the specific port.
Cost range:
16-bit based value range 1-65535,
32-bit based value range 1-200000000.

if-range

no spanning-tree cost This command configures the path cost to default for the specific port.

if-range

spanning-tree port-
priority <0-240>

This command configures the port priority for the specific port.
Default: 128.

if-range

no spanning-tree port-
priority

This command configures the port priority to default for the specific
port.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды